Interfacial Effect-Induced Electrocatalytic Activity of Spinel Cobalt Oxide in Methanol Oxidation Reaction.

In this study, spinel cobalt oxide (Co3O4) nanoparticles without combining with any other metal atoms have been decorated through the influence of two hard templating agents, viz., zeolite-Y and carboxy-functionalized multiwalled carbon nanotubes (COOH-MWCNT). The adornment of the Co3O4 nanoparticles, through the combined impact of the aluminosilicate and carbon framework has resulted in quantum interference, causing the reversal of signatory Raman peaks of Co3O4. Apart from the construction of small Co3O4 nanoparticles at the interface of the two matrices, the particles were aligned along the direction of COOH-MWCNT. The catalyst Co3O4-Y-MWCNT exhibited excellent catalytic activity toward the methanol oxidation reaction (MOR) in comparison to Co3O4-Y, Co3O4-MWCNT, and bared Co3O4 with the current density of 0.92 A mg-1 at an onset potential of 1.33 V versus RHE. The material demonstrated persistent electrocatalytic activity up to 300 potential cycles and 20,000 s without substantial current density loss. High surface area of zeolite-Y in combination with the excellent conductivity of the COOH-MWCNT enhanced the electrocatalytic performance of the catalyst. The simplicity of synthesis, scale-up, and remarkable electrocatalytic activity of the catalyst Co3O4-Y-MWCNT provided an effective way toward the development of anode materials for direct methanol fuel cells.

Role of Transcriptional and Epigenetic Regulation in Lymphatic Endothelial Cell Development.

The lymphatic system is critical for maintaining the homeostasis of lipids and interstitial fluid and regulating the immune cell development and functions. Developmental anomaly-induced lymphatic dysfunction is associated with various pathological conditions, including lymphedema, inflammation, and cancer. Most lymphatic endothelial cells (LECs) are derived from a subset of endothelial cells in the cardinal vein. However, recent studies have reported that the developmental origin of LECs is heterogeneous. Multiple regulatory mechanisms, including those mediated by signaling pathways, transcription factors, and epigenetic pathways, are involved in lymphatic development and functions. Recent studies have demonstrated that the epigenetic regulation of transcription is critical for embryonic LEC development and functions. In addition to the chromatin structures, epigenetic modifications may modulate transcriptional signatures during the development or differentiation of LECs. Therefore, the understanding of the epigenetic mechanisms involved in the development and function of the lymphatic system can aid in the management of various congenital or acquired lymphatic disorders. Future studies must determine the role of other epigenetic factors and changes in mammalian lymphatic development and function. Here, the recent findings on key factors involved in the development of the lymphatic system and their epigenetic regulation, LEC origins from different organs, and lymphatic diseases are reviewed.

Multilayered Composites with Modulus Gradient for Enhanced Pressure-Temperature Sensing Performance.

Highly sensitive and flexible composite sensors with pressure and temperature sensing abilities are of great importance in human motion monitoring, robotic skins, and automobile seats when checking the boarding status. Several studies have been conducted to improve the temperature-pressure sensitivity; however, they require a complex fabrication process for micro-nanostructures, which are material-dependent. Therefore, there is a need to develop the structural designs to improve the sensing abilities. Herein, we demonstrate a flexible composite with an enhanced pressure and temperature sensing performance. Its structural design consists of a multilayered composite construction with an elastic modulus gradient. Controlled stress concentration and distribution induced by a micropatterned structure between the layers improves its pressure and temperature sensing performance. The proposed composite sensor can monitor a wide range of pressure and temperature stimuli and also has potential applications as an automotive seat sensor for simultaneous human temperature detection and occupant weight sensing.

Enhanced Mechanical and Antibacterial Properties of Nanocomposites Based on Poly(vinyl Alcohol) and Biopolymer-Derived Reduced Graphene Oxide.

Functionalized graphene-polymer nanocomposites have gained significant attention for their enhanced mechanical, thermal, and antibacterial properties, but the requirement of multi-step processes or hazardous reducing agents to functionalize graphene limits their current applications. Here, we present a single-step synthesis of thermally reduced graphene oxide (TrGO) based on shellac, which is a low-cost biopolymer that can be employed to produce poly(vinyl alcohol) (PVA)/TrGO nanocomposites (PVA-TrGO). The concentration of TrGO varied from 0.1 to 2.0 wt.%, and the critical concentration of homogeneous TrGO dispersion was observed to be 1.5 wt.%, below which strong interfacial molecular interactions between the TrGO and the PVA matrix resulted in improved thermal and mechanical properties. At 1.5 wt.% filler loading, the tensile strength and modulus of the PVA-TrGO nanocomposite were increased by 98.7% and 97.4%, respectively, while the storage modulus was increased by 69%. Furthermore, the nanocomposite was 96% more effective in preventing bacterial colonization relative to the neat PVA matrix. The present findings indicate that TrGO can be considered a promising material for potential applications in biomedical devices.

Two-Ply Carbon Nanotube Fiber-Typed Enzymatic Biofuel Cell Implanted in Mice.

Implantable devices have emerged as a promising industry. It is inevitable that these devices will require a power source to operate in vivo. Thus, to power implantable medical devices, biofuel cells (BFCs) that generate electricity using glucose without an external power supply have been considered. Although implantable BFCs have been developed for application in vivo, they are limited by their bulky electrodes and low power density. In the present study, we attempted to apply to living mice an implantable enzymatic BFC (EBFC) that was previously reported to be a high-power EBFC comprising carbon nanotube yarn electrodes. To improve their mechanical properties and for convenient implantation, the electrodes were coated with Nafion and twisted into a micro-sized, two-ply, one-body system. When the two-ply EBFC system was implanted in the abdominal cavity of mice, it provided a high-power density of 0.3 mW/cm2. The two-ply EBFC system was injected through a needle using a syringe without surgery and the inflammatory response in vivo initially induced by the injection of the EBFC system was attenuated after 7 days, indicating the biocompatibility of the system in vivo.

Bioinspired, High-Sensitivity Mechanical Sensors Realized with Hexagonal Microcolumnar Arrays Coated with Ultrasonic-Sprayed Single-Walled Carbon Nanotubes.

The development of a flexible electronic skin (e-skin) highly sensitive to multimodal vibrations and a specialized sensing ability is of great interest for a plethora of applications, such as tactile sensors for robots, seismology, healthcare, and wearable electronics. Here, we present an e-skin design characterized by a bioinspired, microhexagonal structure coated with single-walled carbon nanotubes (SWCNTs) using an ultrasonic spray method. We have demonstrated the outstanding performances of the device in terms of the capability to detect both static and dynamic mechanical stimuli including pressure, shear displacement, and bending using the principles of piezoresistivity. Because of the hexagonal microcolumnar array, whose contact area changes according to the mechanical stimuli applied, the interlock-optimized geometry shows an enhanced sensitivity. This produces an improved ability to discriminate the different mechanical stimuli that might be applied. Moreover, we show that our e-skins can detect, discriminate, and monitor various intensities of different external and internal vibrations, which is a useful asset for various applications, such as seismology, smart phones, wearable human skins (voice monitoring), etc.

Exfoliated Graphite Nanoplatelet-Carbon Nanotube Hybrid Composites for Compression Sensing.

In this study, we investigated the gauge factor and compressive modulus of hybrid nanocomposites of exfoliated graphite nanoplatelets (xGnP) and multiwalled carbon nanotubes (MWCNTs) in a polydimethylsiloxane matrix under compressive strain. Mechanical and electrical tests were conducted to investigate the effects of nanofiller wt %, the xGnP size, and xGnP:MWCNT ratio on the compressive modulus and sensitivity of the sensors. It was found that nanofiller wt %, the xGnP size, and xGnP:MWCNT ratio significantly affect the electromechanical properties of the sensor. The compressive modulus increased with an increase in the nanofiller wt % and a decrease in the xGnP size and xGnP:MWCNT ratio. However, the gauge factor decreases with a decrease in the nanofiller wt % and xGnP size and an increase in the xGnP:MWCNT ratio. Therefore, by investigating the piezoresistive effects of various factors for sensing performance, such as wt %, xGnP size, and xGnP:MWCNT ratio, the concept of one- and two-dimensional hybrid fillers provides an effective way to tune both mechanical properties and sensitivity of nanocomposites by tailoring the network structure of fillers.

Angle Sensor Module for Vehicle Steering Device Based on Multi-Track Impulse Ring.

In step with the development of Industry 4.0, research on automatic operation technology and components related to automobiles is continuously being conducted. In particular, the torque angle sensor (TAS) module of the steering wheel system is considered to be a core technology owing to its precise angle, torque sensing, and high-speed signal processing. In the case of conventional TAS modules, in addition to the complicated gear structure, there is an error in angle detection due to the backlash between the main and sub-gear. In this paper, we propose a multi-track encoder-based vehicle steering system, which is incorporated with a TAS module structure that minimizes the number of components and the angle detection error of the module compared with existing TAS modules. We also fabricated and tested an angle detection signal processing board and evaluated it on a test stand. As a result, we could confirm its excellent performance of an average deviation of 0.4° and applicability to actual vehicles by evaluating its electromagnetic interference (EMI) environmental reliability. The ultimate goal of the TAS module is to detect the target steering angle with minimal computation by the steering or main electronic control unit (ECU) to meet the needs of the rapidly growing vehicle technology. The verified angle detection module can be applied to an actual steering system in accordance with the mentioned technical requirements.

Woven Kevlar Fiber/Polydimethylsiloxane/Reduced Graphene Oxide Composite-Based Personal Thermal Management with Freestanding Cu-Ni Core-Shell Nanowires.

Thermotherapy is a widespread technique that provides relief for muscle spasms and joint injuries. A great deal of energy is used to heat the surrounding environment, and heat emitted by the human body is wasted on our surroundings. Herein, a woven Kevlar fiber (WKF)-based personal thermal management device was fabricated by directly growing vertical copper-nickel (Cu-Ni) nanowires (NWs) on the WKF surface using a hydrothermal method. The treated WKF was combined with reduced graphene oxide (rGO) dispersed in polydimethylsiloxane (PDMS) to form composites using vacuum-assisted resin transfer molding (VARTM). This WKF-based personal thermal management system contained a conductive network of metallic NWs and rGO that promoted effective Joule heating and reflected back the infrared (IR) radiation emitted by the human body. It thus behaved as a type of thermal insulation. The Cu-Ni NWs were synthesized with a tunable Ni layer on Cu core NWs to enhance the oxidation resistance of the Cu NWs. The combined effect of the NW networks and rGO enabled a surface temperature of 70 °C to be attained on application of 1.5 V to the composites. The Cu3Ni1-WKF/PDMS provided 43% more thermal insulation and higher IR reflectance than bare WKF/PDMS. The absorbed impact energy and tensile strength was highest for the Cu1Ni3- and rGO-integrated WKF/PDMS samples. Those Cu-Ni NWs having higher Ni contents displayed better mechanical properties and those with higher Cu contents showed higher Joule heating performance and IR reflectivity at a given rGO loading. The composite shows sufficient breathability and very high durability. The high flexibility of the composites and their ability to generate sufficient heat during various human motions ensures their suitability for wearable applications.

Fabrication and Synthesis of Highly Ordered Nickel Cobalt Sulfide Nanowire-Grown Woven Kevlar Fiber/Reduced Graphene Oxide/Polyester Composites.

Well-aligned NiCo2S4 nanowires, synthesized hydrothermally on the surface of woven Kevlar fiber (WKF), were used to fabricate composites with reduced graphene oxide (rGO) dispersed in polyester resin (PES) by means of vacuum-assisted resin transfer molding. The NiCo2S4 nanowires were synthesized with three precursor concentrations. Nanowire growth was characterized using scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy. Hierarchical and high growth density of the nanowires led to exceptional mechanical properties of the composites. Compared with bare WKF/PES, the tensile strength and absorbed impact energy were enhanced by 96.2% and 92.3%, respectively, for WKF/NiCo2S4/rGO (1.5%)/PES. The synergistic effect of NiCo2S4 nanowires and rGO in the fabricated composites improved the electrical conductivity of insulating WKF/PES composites, reducing the resistance to ∼103 Ω. Joule heating performance depended strongly on the precursor concentration of the nanowires and the presence of rGO in the composite. A maximum surface temperature of 163 °C was obtained under low-voltage (5 V) application. The Joule heating performance of the composites was demonstrated in a surface deicing experiment; we observed that 17 g of ice melted from the surface of the composite in 14 min under an applied voltage of 5 V at -28 °C. The excellent performance of WKF/NiCo2S4/rGO/PES composites shows great potential for aerospace structural applications requiring outstanding mechanical properties and Joule heating capability for deicing of surfaces.

Pd/Cu-Oxide Nanoconjugate at Zeolite-Y Crystallite Crafting the Mesoporous Channels for Selective Oxidation of Benzyl-Alcohols.

Solid-state grinding of palladium and copper salts allowed the growth of palladium/copper oxide interface at the zeolite-Y surface. The hybrid nanostructured material was used as reusable heterogeneous catalyst for selective oxidation of various benzyl alcohols. The large surface area provided by the zeolite-Y matrix highly influenced the catalytic activity, as well as the recyclability of the synthesized catalyst. Impregnation of PdO-CuO nanoparticles on zeolite crystallite leads to the generation of mesoporous channel that probably prevented the leaching of the metal-oxide nanoparticles and endorsed high mass transfer. Formation of mesoporous channel at the external surface of zeolite-Y was evident from transmission electron microscopy and surface area analysis. PdO-CuO nanoparticles were found to be within the range of 2-5 nm. The surface area of PdO-CuO-Y catalyst was found to be much lower than parent zeolite-Y. The decrease in surface area as well as the presence of hysteresis loop in the N2-adsoprtion isotherm further suggested successful encapsulation of PdO-CuO nanoparticles via the mesoporous channel formation. The high positive shifting in binding energy in both Pd and Cu was attributed to the influence of zeolite-Y framework on lattice contraction of metal oxides via confinement effect. PdO-CuO-Y catalyst was found to oxidize benzyl alcohol with 99% selectivity. On subjecting to microwave irradiation the same oxidation reaction was found to occur at ambient condition giving same conversion and selectivity.

Microwave-synthesized freestanding iron-carbon nanotubes on polyester composites of woven Kevlar fibre and silver nanoparticle-decorated graphene.

We synthesized Ag nanoparticle-decorated multilayered graphene nanosheets (Ag-graphene) from graphite nanoplatelets and silver nitrate through 90-100 s of microwave exposure, without the use of any mineral acids or harsh reducing agents. Fe nanoparticle-decorated carbon nanotubes (Fe-CNTs) were grown on polypyrrole (PPy) deposited on woven Kevlar fibre (WKF), using ferrocene as a catalyst, under microwave irradiation. Fe-CNTs grown on WKF and Ag-graphene dispersed in polyester resin (PES) were combined to fabricate Ag-graphene/Fe-CNT/PPy-coated WKF/PES composites by vacuum-assisted resin transfer moulding. The combined effect of Fe-CNTs and Ag-graphene in the resulting composites resulted in a remarkable enhancement of tensile properties (a 192.56% increase in strength and 100.64% increase in modulus) as well as impact resistance (a 116.33% increase). The electrical conductivity significantly increased for Ag-graphene/Fe-CNT/PPy-coated WKF/PES composites. The effectiveness of electromagnetic interference shielding, which relies strongly on the Ag-graphene content in the composites, was 25 times higher in Ag-graphene/Fe-CNT/PPy-coated WKF/PES than in neat WKF/PES composites. The current work offers a novel route for fabricating highly promising, cost effective WKF/PES composites through microwave-assisted synthesis of Fe-CNTs and Ag-graphene.

Poly(vinyl alcohol) reinforced and toughened with poly(dopamine)-treated graphene oxide, and its use for humidity sensing.

Poly(dopamine)-treated graphene oxide/poly(vinyl alcohol) ("dG-O/PVA") composite films were made and characterized. G-O was modified with poly(dopamine) in aqueous solution and then chemically reduced to yield poly(dopamine)-treated reduced G-O. A combination of hydrogen bonding, strong adhesion of poly(dopamine) at the interface of PVA and G-O sheets, and reinforcement by G-O resulted in increases in tensile modulus, ultimate tensile strength, and strain-to-failure by 39, 100, and 89%, respectively, at 0.5 wt % dG-O loading of the PVA. The dG-O serves as a moisture barrier for water-soluble PVA, and the dG-O/PVA composite films were shown to be effective humidity sensors over the relative humidity range 40-100%.

Organelle-selective fluorescent Cu2+ ion probes: revealing the endoplasmic reticulum as a reservoir for Cu-overloading.

Two novel Cu(2+) sensors, 1 and 2, bearing naphthalimide and a DPA moiety were synthesized to study copper accumulation in organelles by selective Cu(2+) sensing. The ER-selective Cu(2+) sensor 1 that we developed serves as a valuable tool for understanding the subcellular compartmentalization and roles of copper ions in physiology and pathophysiology.

Simultaneous detection of major enteric viruses using a combimatrix microarray.

Various enteric viruses including norovirus, rotavirus, adenovirus, and astrovirus are the major etiological agents of food-borne and water-borne disease outbreaks and frequently cause non-bacterial gastroenteritis worldwide. Sensitive and high-throughput detection methods for these viral pathogens are compulsory for diagnosing viral pathogens and subsequently improving public health. Hence, we developed a sensitive, specific, and high-throughput analytical assay to detect most major enteric viral pathogens using "Combimatrix" platform oligonucleotide probes. In order to detect four different enteric viral pathogens in a sensitive and simultaneous manner, we first developed a multiplex RT-PCR assay targeting partial gene sequences of these viruses with fluorescent labeling for the subsequent microarray. Then, five olignonucleotides specific to each of the four major enteric viruses were selected for the microarray from the oligonulceotide pools targeting the specific genes obtained by multiplex PCR of these viruses. The oligonucleotide microarray was evaluated against stool specimens containing single or mixed viral species. As a result, we demonstrated that the multiplex RT-PCR assay specifically amplified partial sequences of four enteric viruses and the subsequent microarray assay was capable of sensitive and simultaneous detection of those viruses. The developed method could be useful for diagnosing enteric viruses in both clinical and environmental specimens.

Alternative estimation of human exposure of single-walled carbon nanotubes using three-dimensional tissue-engineered human lung.

Recent discoveries of various forms of carbon nanostructure have stimulated research on their applications and hold promise for applications in medicine and other related engineering areas. Although carbon nanotubes (CNTs) are already being produced on a massive scale, few studies have been performed which test the potential harmful effects of this new technology. The authors used a three-dimensional in vitro model of the human airway using a coculture of normal human bronchial epithelial cells and normal human fibroblasts for the health risk assessment of CNTs on the human respiratory systems. The authors used aqueous single-walled carbon nanotube (SWCNT) solution. The average length and diameter of nanotube ropes were about 500 nm and less than 10 nm, respectively. The authors measured the production of nitric oxide (NO) as an inflammatory marker and mitochondrial activity using MTT (3-(4,5-Dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide) assay as a cytotoxic response of the cell layers following exposure of different concentration of aqueous SWCNT solution. The results indicated that NO production was dramatically increased and cell viability was decreased following exposure of different concentrations of SWCNTs. Transepithelial electrical resistance (TER) across the coculture layers was measured to observe the changes in airway physiological function following exposure of different concentrations of SWCNTs. TER value was dramatically decreased following exposure of 20% SWCNT (8 microg/ml). In this study, the authors presented viable alternatives to in vivo tests to evaluate the toxicity of engineered SWCNTs. Cytotoxic/inflammatory responses and barrier function of the human lung layers following exposure of SWCNTs were observed using in vitro coculture system of airway.

Mechanical and electrical properties of polycarbonate nanotube buckypaper composite sheets.

The thermogravimetric, mechanical, and electrical properties of composite sheets produced by infiltrating single-wall carbon nanotube films (also known as 'buckypapers') with polycarbonate solution were characterized. The composite sheets showed improved stiffness and toughness, while the electrical conductivity decreased, as compared to a neat buckypaper. In addition, polycarbonate/buckypaper composite sheets showed higher resistance to handling and processing damages. Experimental results suggest the viability of the infiltration process as a means to toughen buckypapers and to fabricate polymer/carbon nanotube composites having high nanotube concentration and controlled nanotube structure.